pvb, pvm pecl vcxo series 6 pad leadless surface mount or 4 lead thru-hole pecl voltage controlled xtal oscillator differential pecl output with enable/disable standard specifications part numbering guide consult factory for available frequencies and specs. not all options available for all frequencies. a special part numbe r may be assigned. frequency stability is inclusive of frequency shifts due to calibration, temperature, supply voltage, shock, vibration a nd load (425) 776 - 1880, fax: (425) 776 - 2760, ple - sales@pletronics.com, www.pletronics.com 20 pl tronics, inc. packaging pvm = tube pvb = tube or 24mm tape 16mm pitch portions of the part number that appear after the frequency may not be marked on part (c of c provided) mar 2004 overall frequency stability operating temperature range 0 to +70 c is standard, but can be extended to storage temperature range - 55 to +125 c - 40 to +85 c supply voltage (vcc) 3.3 volts 5 % standard, but 5.0 volts or 2.5 volts also available. see t est cirucit 5. e/d internal pullup 50 kohm minimum to vcc pvb output enable/disable (e/d) output enable time output disable time when disabled output symmetry 45/55% referenced to 50% of amplitude output rise & fall (tr & tf) 1.0 ns maximum when vth is 10% and 90% of waveform < 250 mhz = 90 ma maximum, 250 mhz and above = 100 ma maximu m supply current (icc) 2.275 v minimum referenced to ground, vcc = 3.300v, 0.975 v minimum referenced to termination voltage, - 1.025 v minimum referenced to vcc output high level 1.680 v maximum referenced to ground, vcc = 3.300v, 0.380 v maximum referenced to termination voltage, - 1.620 v maximum referenced to vcc output low level 6 ps rms maximum measured from 12 khz to 20 mhz from output frequency jitter v enable 0.7 vcc minumum referenced to ground 0.3 vcc maximum referenced to ground v disable 100 ns maximum 100 ns maximum output disable time q output = logic low, qn output = logic high. both outputs a re active 50 ppm, linerarity slope positive and montonic control voltage range (cvr) for 5.0 vcc, cvr = 0.5 to 4.5 v, for 3.3 vcc, cvr = 0.0 to 3 .3 v, for 2.5 vcc, cvr = 0.0 to 2.5 v pullability pull range is defined as absolute pull range. this is the pu ll range about the specified oscillator frequency, independent of supply, temperature range and load. typical v alues are 25, 50 and 100 ppm. 10% typical 25 ppm, 20 ppm over operating temperature range frequency stability frequency in mhz frequency deviation (pullability) absolute pull range pvb 5 v b v - 100.0m - xxx (internal code or blank) v: 50 ppm w = 100 ppm operating temperature range b: 0 to +70 c f: - 40 to +85 c 5 = 50 ppm 4 = 25 ppm 2 = 20 ppm pvb = b pkg pvm = metal model supply voltage y = 5.0 volts 10 % v = 3.3 volts 5 % w = 2.5 volts 5 % 1.00 mhz ? 650.00 mhz consult factory for higher frequencies pl tronics , inc. 19013 36th ave. w, suite h lynnwood, wa 98036 usa manufacturer of high quality frequency control products .
pvb, pvm pecl vcxo series (425) 776 - 1880, fax: (425) 776 - 2760, ple - sales@pletronics.com, www.pletronics.com 20a pl tronics, inc. mechanical: not to scale inches (mm) solder pads due to part size and factory abilities, part marking may var y from lot to lot and may contain our part number or an inte rnal code. mar 2004 1 vcon 2 e/d 3 gnd 4 q out 5 qn out 6 vcc pin signal 1 vcon 7 gnd 8 out 14 vcc pin signal see page 6 for layout guidelines pvb series pvm series 0.055 (1.4) 0.200 (5.08) 1 3 4 2 5 6 0.228 (5.8) 0.118 (3.0) 0 .145 (3.68) 0.400 (10.16) max 0.560 (14.23) max 0.195 (4.95) max 0.200 (5.08) 1 2 3 4 5 6 .807 (20.5) max .500 (12.7) max .200 (5.08) max .600 (15.24) .300 (7.62) 1 7 14 8 .031 (0.8) .250 (6.35) max .020 (.51) pl tronics , inc. 19013 36th ave. w, suite h lynnwood, wa 98036 usa manufacturer of high quality frequency control products .
|
